Namespace: Autodesk.Revit.DB

BuiltInFailures.MEPFabricationFailures

Class

Description:
Failures about MEP fabrication.

Inheritance Hierarchy:
System.Object
Autodesk.Revit.DB.BuiltInFailures.MEPFabricationFailures

Syntax

public static class MEPFabricationFailures

Public NotInheritable Class MEPFabricationFailures

public ref class MEPFabricationFailures abstract sealed

[<AbstractClassAttribute>]
[<SealedAttribute>]
type MEPFabricationFailures = class end

BuiltInFailuresMEPFabricationFailures Class Members:

Name	Description
AdditionalPartNotLoaded	An additional part was not loaded.
CannotConvertFlexPipeToPart	Cannot convert flex pipe to fabrication part.
CannotMatchFabricationHangerSizeToHost	The hanger cannot be re-sized to match the re-sized host.
FabDbChangeConn	Fabrication Database changes altered connectivity
FabDbOpenJobConn	Fabrication job imported had bad connectivity
FabDbSwapOut	Fabrication Database reload could not swap out for newer parts.
FabricationConfigurationCorrupted	It looks that the Fabrication Configuration %1!s! was corrupted, please check it at %2!s!.
FabricationHangerCannotBeSloped	A hanger cannot be sloped or placed on a sloped element.
FabricationHangerHostNotFound	The hanger will disconnect because we can't find the suitable host.
FabricationHangerNotConnectToHost	Fabrication Hanger didn't connect to the %s host.
FabricationHangerOutOfHost	The hanger is out of its host and will be disconnected.
FabricationHangerSizeNotMatch	The hanger size does not match the size of the host, so it can not be connected.
FabricationOutOfSizeCondition	The fabrication part size is not within the correct size range for the service button condition.
FabricationOverSizedCheck	Fabrication part is too large to fit on the sheet metal. Replace the part with multiple smaller parts, or notify the CAM operator.
FabricationPartBadConnectionAlignmentWarning	The connection invalid due to the connector are not aligned and/or this is a gap between the connectors.
FabricationPartBadConnectionConnectivityWarning	The connection invalid due to connection types associated to the connectors are not compatible.
FabricationPartBadConnectionSizeWarning	The connection invalid due to connectors sizes are not the same.
FabricationPartCannotBeMirrored
FabricationPartCannotChangeServiceSizeWarning	The selected fitting(s) cannot successfully change service or change size. You must disconnect the connections on the fitting(s) and try again.
FabricationPartCannotChangeSlopeError	The connected fitting(s) cannot successfully change to the new slope value. You may try to disconnect the connections on the fitting(s) and try again.
FabricationPartCannotChangeTypeBadDimError	The selected fitting(s) cannot successfully change the type. The newly selected fabrication part may have badly configured dimensions or be constrained due to connected fitting(s). You may try to disconnect the connections on the fitting(s) and try again.
FabricationPartCannotChangeTypeBadDimUnConnError	The selected fitting(s) cannot successfully change the type. The newly selected fabrication part may have badly configured dimensions, resulting in bad geometry.
FabricationPartCannotChangeTypeError	The selected fitting(s) cannot successfully change the type. You must disconnect the connections on the fitting(s) and try again.
FabricationPartCannotChangeTypeIncompatError	The selected fitting(s) cannot successfully change the type. The newly selected fabrication part type either has no material or has badly configured dimensions, resulting in bad geometry. You may try to disconnect the connections on the fitting(s) and try again.
FabricationPartCannotChangeTypeIncompatUnConnError	The selected fitting(s) cannot successfully change the type. The newly selected fabrication part type either has no material or has badly configured dimensions, resulting in bad geometry.
FabricationPartCannotChangeTypeMisalignedError	The selected fitting(s) cannot successfully change the type. The newly selected fabrication part type has a problem with the angle dimension of the current fitting(s), resulting in bad geometry. You may try to disconnect the connections on the fitting(s) and try again.
FabricationPartCannotChangeTypeMisalignedUnConnError	The selected fitting(s) cannot successfully change the type. The newly selected fabrication part type has a problem with the angle dimension of the current fitting(s), resulting in bad geometry.
FabricationPartCannotChangeTypeUnConnError	The selected fitting(s) cannot successfully change the type.
FabricationPartCannotChangeTypeWarning	The selected fitting(s) cannot maintain connections to existing fabrication parts due to size, direction or angle differences. You must manually reconnect the open connections.
FabricationPartExceededAngleFlexToleranceWarning	The angle flex is greater than the maximum angle flex tolerance defined by the fabrication part. Connections with this part may not be properly aligned and may appear to be skewed.
FabricationPartExcludedPartWarning	There were fabrication parts needed to the make the connection that were excluded from the fabrication service causing the connection to fail. You may try to inlcude these fitting(s) and try again.
FabricationPartFitFailure	Fabrication Part Fitting Failed to Fit
FabricationPartFitFailWarning	Fabrication Part Fitting Failed to Fit
FabricationPartHasInvalidGeometry	The fabrication part either has no material or has badly configured dimensions, resulting in bad geometry.
FabricationPartInvalidConnection	Fabrication Part connection invalid and could not be automatically coupled.
FabricationPartInvalidSpecification	The part specification is invalid.
FabricationPartNoPartTypeFound	There are no fabrication part types found for the current Configuration and Service. Please select settings and reload the service to create the fabrication part types.
FabricationPartNotAttachedToStraight	The part must be attached to straight.
FabricationPartOptimizeInvalidConnection	No available couplings to connect standard lengths for this instance of straight.
FabricationRodDetachFromHangerError	The rod need to be detached from hanger.
FabricationRodsConnectionChangedWarning	The structural component that the hanger is attached to has changed to a different element.
FabricationRodsDisconnectedError	The hanger rod was disconnected because there is no structural component above.
FabricationRodsDisconnectedWarning	The hanger rod was disconnected because there is no structural component above.
FabricationServiceMismatch	Attempting to connect fabrication parts from different services.
FabricationStraigtLengthOversized	Fabrication straight exceeds the standard length. Use the Optimize Length command to adjust the length.
FixedFabricationPartNotChangeLength	Failed to change length of fixed part.
GroupedFabricationPartNotReposition	Failed to reposition part.
HangerProfileNotMatchWithHost	The defined hanger profile does not match with the host.
HangerWidthOutOfRange	The hanger width is too large to show.
InvalidConnectionsHaveBeenDisconnected	Invalid connections have been disconnected. Please reconnect them manually or use different fittings.
InvalidSelectionThereCannotBeOpenConnectors	Invalid selection there cannot be any open connectors for the design to fabrication part tool.
NoStructuralHostToAttachWarning	There is no structural component to attach the hanger rod to.
NotAllPartsWereConvertedUnsuportedFittingOffsets	Not all parts were converted. Eccentric transitions and taps that have offsets from the center line are unsupported and cannot be converted.
PinnedFabricationPartNotChangeExtension	Failed to change extension of part.
PinnedFabricationPartNotReposition	Failed to reposition part.
PlaceCutinFittingFailed	Failed to insert part.
SizeNotAvailableInFabricationService	Sizes:%1!s! in system %2!s! are not available in fabrication service:%3!s!, All available sizes are:\n%4!s!.
UneditableFabricationPartNotReposition	Failed to reposition part.