RVTDocs.com
Namespace: Autodesk.Revit.DB

BuiltInFailures.StairRampFailures

Class
Description:
Failures about StairRamp.
Inheritance Hierarchy:
System.Object
  Autodesk.Revit.DB.BuiltInFailures.StairRampFailures
Syntax 
public static class StairRampFailures
BuiltInFailuresStairRampFailures Class Members:
Name Description
ActualRiserHeightChanged The actual riser height for one or more stairs violates the maximum set in the type.
AntiparallelRampRisers Riser lines are parallel but not collinear. Can't build Run between these Risers.
AntiparallelRampRisersError Riser lines are parallel but not collinear. Can't build Run between these Risers.
ArcRunRadiusTooSmall Can't create Run. Run radius is too small.
ArcRunWidthTooLongFailure Arc run width is too long.
AutomaticLandingConvertedToSketchedLandingWarning Some run(s) are deleted, so automatic landing is converted to sketched landing.
BadBalustersPerTread Number of Balusters per Tread must be an integer greater than zero.
BadFillingSpacing Spacing for Excess Length Fill is too small.
BadRailings Can't create Railings.
BadRailingsError Can't create Railings.
BadRailProfile One or more Profile Loops are invalid, probably because of self-intersection.
BadTreadRiserProfile Tread/Riser profile is invalid.
BalustersTooClose Baluster Separation must be equal to or greater than the Baluster widths.
BalustersTooCloseAbsolute Baluster Separation is too small.
BalusterUpsideDown Top reference is below Bottom reference for one or more Balusters. These Balusters are not created.
CannotAlignSupportOnPosts Cannot align the support on the posts.
CannotComputeRailElevation Can't compute elevation profile for one or more Rails
CannotCreateBaluster Can't create Balusters for given Width and Height.
CannotCreateBalusterPatterns Can't create Baluster Patterns for Railings
CannotCreateCornerBalusters Can't create corner Baluster
CannotCreateLandingStringer Can't create stringer at landing.
CannotCreateMiddleStringer Can't create one or more Middle Stringers.
CannotCreateMonolithicStairs Can't make monolithic Stairs.
CannotCreateNosing Can't create nosing on one or more treads.
CannotCreateOneOrMoreBaluster Can't create one or more Balusters
CannotCreateOneOrMoreTreads Can't create geometry for one or more treads.
CannotCreateOpenMiddleStringers Can't cut open/middle stringers geometry.
CannotCreateRail Can't create Railing. Thickness of Rail or Balusters might be too small. If you don't want Balusters, specify "None" for Baluster Shape.
CannotCreateRailGeom Can't create geometry for one or more Rails
CannotCreateRailWarn Can't create Railing. Thickness of Rail or Balusters might be too small. If you don't want Balusters, specify "None" for Baluster Shape.
CannotCreateRiser Can't create geometry for one or more risers.
CannotCreateSideStringer Can't create one or more Side Stringers.
CannotCreateStairForLevelOverlapping Some of the multistory stairs couldn't be created due to the overlapped levels.
CannotCreateStringers Can't create stringers geometry.
CannotDrawStairs Can't make stairs
CannotDrawStairsError Can't make stairs
CannotEndWithZeroRiser Can't end Stairs with Riser because Riser Thickness is too small.
CannotGenerateFaces Couldn't generate surfaces for stairs.
CannotGenerateFacesError Couldn't generate surfaces for stairs.
CannotGenerateRamp Couldn't generate surfaces for ramp.
CannotGenerateRampError Couldn't generate surfaces for ramp.
CannotMakeLanding Can't make landing.
CannotOffsetBoundary Can't create Boundary as an offset of Run Curve
CannotOffsetRail Can't create one or more Rails with desired offset
CannotPlaceBalusterOffset Can't place Balusters and/or Rails with desired offset
CannotPlaceBalusterPatterns Can't place Baluster Patterns
CannotPlaceRailingOnStringerWarning Railing is placed on tread because there is no stringer.
CannotProcessInStairsSketchEditMode Cannot process when stair(s) in sketch edit mode.
CannotSplitRailingWithExtensions Railings with extensions cannot be split.
ContinuousRailFilletCreationError Cannot create specified fillet at rail path corner.
ContinuousRailFilletCreationParallel Cannot create specified fillet at rail path corner because of the curves are already smoothed.
ContinuousRailFilletCreationWarning Cannot create specified fillet at rail path corner.
ContinuousRailGometryCreationFailure Cannot create the continuous rail geometry.
ContinuousRailNotContinuous The rail is non-continuous.
ContinuousRailSupportPlacementFailure Cannot place the supports along the rail path.
ContinuousRailTransitionFailure Cannot create specified transition at rail path turn, hand Rail/Top Rail cannot maintain continuous.
ExtendBelowBaseGreaterThanLandingBaseElevation Extend Below Base needs to be less than Landing Base Elevation.
ExtendBelowBaseGreaterThanRunTopElevation Extend Below Base needs to be less than Run Top Elevation.
FailToReOrientSketchCurvesFailure Failed to orient sketch curves.
HeightOfRunIsTooSmall Height of run is too small.
IntermediateLandingHigherThanTopRunFailure Run is reversed.
InvalidBalustersPattern Invalid Balusters Pattern
InvalidLocationLineJustificationFailure Modify the location justification to a invalid value.
InvalidParameters Stairs run or landing has invalid parameter(s).
InvalidRailProfile Profiles for one or more of the Rails are invalid. Make sure that every used Profile is a closed series of non-intersecting Lines.
InvalidStairsPathFailure Invalid stairs path provided.
InvalidStartLevel The start level and end level for this staircase must be at different elevations.
InvalidStartLevelRamp The start level and end level for this ramp must be at different elevations.
LandingDepthIsLessThanRunWidthWarning Landing depth is less than run width.
LandingHeightUnderStairsBottom Cannot make landing because height of landing is equal or less than to bottom height of the stair.
LandingShapeHandleOnPinnedRunFailure Cannot Drag the automatic landing shape handle control because the connected run is pinned.
MayUnjoinRailAndSupports Fillet may cause the supports unjoin with the rail.
MultistoryLevelBelowTopbottomLevel Multistory top level must be above the stair/ramp top and bottom levels.
MultistoryLevelBelowTopbottomLevelError Multistory top level must be above the stair/ramp top and bottom levels.
MultistoryStairDoesntReach The multistory stair/ramp could not reach its top level with integral number of flights. Maximum number of flights below the top level is created.
MultistoryStairsAutomaticLevelLandingsDeleted Level landings are deleted because the connected stairs have been regenerated.
MultistoryStairsComponentJoinFailure Can't keep elements joined. Avoid converting stairs to skeched-based component in Multistory stairs.
MultistoryStairsHideTopLevelParameter You have set the stair's multistory top level to None, and Revit will remove this parameter, if you want to create a multistory stair, please use Create Multistory Stair feature.
MultistoryStandardStairBottomEndExceedsOrNotReach One of the stairs inside multistory stairs bottom ends exceeds or cannot reach the base elevation of the stair.
MultistoryStandardStairTopEndExceedsOrNotReach One of the stairs inside multistory stairs top ends exceed or cannot reach the top elevation of the stair.
MultusegmentRampRiser Ramp can't have multisegment Riser.
MultusegmentRampRiserError Ramp can't have multisegment Riser.
NoCurvesInRailing Railing Sketch has no Lines.
NoProfileForRail Must specify Profiles for every Rail.
NoRailingsStringer Railings and Stringers will not be automatically generated due to bad Runs. This message may be incorrect if you have Edited the Sketch and modified some dimensions.
NoRisersInPureMonolithicStairs Monolithic Stairs with zero tread thickness can't have risers
NoRunsRamp Ramp has no Runs. Can't create Ramp.
NoRunsRampError Ramp has no Runs. Can't create Ramp.
NotALineRiserRamp Riser line must be a straight line for Ramps.
NotALineRiserRampError Riser line must be a straight line for Ramps.
NotchThicknessIsLargerThanLandingWarning The notch thickness is larger than landing.
NotEnoughRisers Actual Number of Risers is different from Desired Number of Risers. Add/remove Risers or change Desired Number of Risers in Stairs Properties.
OnlyMonolithicStairs Tread thickness can't be zero for non-monolithic stairs
PartOfRiserLiesOnBoundaryFailure Part of the riser lies on the boundary is not allowed.
PathDoesntJoinToBorderRisersFailure Path doesn't join to border risers is not allowed.
RailCurveTooShort Curve in rail sketch is too short for rail creation and ignored.
RailingBadOffset An arc in the railing sketch has a radius that conflicts with the current rail widths and offsets. Please either increase the radius or modify rail profiles and offsets.
RailingCurvesNotSplitRamp The slope of this railing will not parallel the ramp at landings. To get a parallel railing, split the railing sketch at the ends of landings.
RailingCurvesNotSplitStairs The slope of this railing may not parallel the stairs at runs and landings. To get a parallel railing, split the railing sketch at the ends of landings.
RailingDoublyConnected Railings hosted on Stairs must form a single, open, connected line.
RailingNotConnected The Railing line must be a single connected Sketch. If you want separate pieces of Railing, create two or more separate Railings.
RailPathCloseLoopForExtensionWarning The rail path is closed at the start and end path point for extension creation.
RailPlacedOutsideOfHost Railings are placed completely outside the host. It may change the adjustment of the railing to the host and its vertical position.
RailProfileLowerThanFilletError Fillet cannot be created between rail segment since the radius is lower than the profile size.
RailProfileLowerThanFilletFailure Fillet cannot be created between rail segment since the radius is lower than the profile size.
RailProfileOpen Open Profile Loop can't be used as a Rail Profile
RailTypeChangeInconsistancyWarningWithResetBtn Some rail type changes are not consistent with your rail instances customization in this project, you can reset them to make them corresponding with your changes.
RampDoesntReach The ramp is not long enough to reach the top constraint. Change the slope or increase the length of the ramp.
RampDoesntReachOffset The ramp is not long enough to reach the top constraint plus top offset. Change the slope or increase the length of the ramp.
RampLandingNotCreated Beginning of run coincide with the end of previous run. Landing is not created between runs.
RampRunTooComplex Ramp Run has complex boundary and may produce unreasonable geometry. Split it into few Runs by inserting Riser Lines at the end of each Run and at the beginning of the next one. If you want to create Ramp with arc an straight section you can do it using a Run tool.
RampStartHigherThanEnd The ramp's base (base level + base offset) must be below its top (top level + top offset).
RiserCurveTooShort Riser curve is too short to create nosing on it.
RiserHeightIsTooSmall Riser height is too small.
RiserIntWithBoundaryMoreThanOnceFailure Riser intersects with boundary more than once.
RisersAtSameLocation The highlighted risers have the same location along the boundary line. Please move one of the two risers.
RiserThicknesssResetToZero Monolithic Stairs without Treads can't have Risers. Riser Thickness for Stairs Type was automatically set to zero.
RunBottomHigherThanTopFailure The base elevation for the run is higher than the top elevation for the run.
RunBottomUnderStairsBottomFailure Run bottom elevation should not be below the stairs bottom elevation.
RunIsJoiningLandingWithRiserSoNotchDoesNotWorkWarning Run is joining landing with riser, so notch configuration does not take effect. Try to set run as begin/end with tread to make a notch.
RunTopLowerThanBottomFailure The top elevation for the run is lower than the base elevation for the run.
SpiralRunRadiusTooSmallFailure The radius value for the run is too small.
StairIncompleteFailure Stair element is incomplete, not all components are logic connected.
StairsActualRiserHeightGreaterThanMaximumFailure Computed actual riser height of stairs is greater than maximum riser height defined in stairs type.
StairsActualRunWidthLessThanMinimumFailure Actual run width is less than minimum run width defined in stairs type.
StairsActualTreadDepthLessThanMinimumFailure Computed actual tread depth of stairs is less than minimum tread depth defined in stairs type.
StairsAlreadyAttachedToCurrentLevel Mutistory Stairs already have a Stair attaching to this level.
StairsAreUpdatedDueToLevelHeightChange Stair component(s) in the multistory stair are updated due to the level height changes.
StairsAutomaticLandingLayoutFailure Fail to generate the automatic landing layout
StairsAutomaticLandingLayoutWarn Fail to generate the automatic landing layout
StairsBottomEndExceedsOrNotReachWarning Stair bottom end exceeds or cannot reach the base elevation of the stair. Add/remove risers at the bottom end or change base elevation settings in Stair Properties.
StairsCannotExtendToFloorStructureLayerWarning Stairs cannot extend to floor structure layer.
StairsCommonRunGenerateLayoutFailure Fail to get base line thus fail to generate run layout
StairsComponentJoinFailure Can't keep elements joined.
StairsCrossingRisersDisallowedFailure Crossing risers are not allowed
StairsGenericFailure Stairs generic failure
StairsGenericTransformFailure Cannot change base elevation of Stairs
StairsIllegalDesiredNumRisers Desired Number of Risers is too small. Computed Actual Riser Height is greater than Maximum Riser Height allowed by type.
StairsInMultistoryExceedTopConstraint Stairs in MultistoryStairs after adjusting still exceed the top constraint.
StairsOnlySingleBoundaryHasRiserWithBothEndsOnBoundaryFailure Only single boundary case may have riser with its both ends on boundary.
StairsOtherThan2IntsByRiserAndBoundaryFailure More than 2 intersection points between riser segment and boundary encountered
StairsPathPositionResetWarning The stairs path doesn't intersect with riser lines.
StairsRunRunJoinNotAllowedFailure Run-Run join is not allowed of they have same "Start With Riser"/"End With Riser" configuration at the joined end.
StairsStartHigherThanEnd The stairs' base (Base Level + Base Offset) must be below its top (Top Level + Top Offset).
StairsStringerCannotBeCreated The stairs stringer cannot be created.
StairsSubElementsNotConnectedWarning Stair sub-elements are not connected
StairsSupportOverlapFailure Some supports overlap with others
StairsSupportTooShort A short support is being created.
StairsTopEndExceedsOrNotReachWarning Stair top end exceeds or cannot reach the top elevation of the stair. Add/remove risers at the top end or change top elevation settings in Stair Properties.
StairsTopLowerThanBaseFailure The top of the Stair is lower than the base of the Stair
StairStringerCantOffset Inside stringer could not be created because of insufficient space. Please disable the inside stringer or decrease its width.
StairsWinderGenLayoutFailure Fail to generate run layout and then cannot make winder run
StairsWinderInvalidParamsFailure Cannot create the winder run because some values for the instance properties cannot be satisfied.
StairsZeroDesiredRisers The number of desired risers for a staircase cannot be 0.
StringerCurvesNotSplitStairs The slope of stringer may not parallel runs and landings. To get a parallel stringer, split boundary lines at the ends of landings.
StringerCurveTooShort A piece of boundary is too short to create stringer on it.
TooShortCurveDowngradeGeometry Curve is too short and may downgrade the geometry.
TreadDepthBelowMin The Actual Tread Depth for one or more Stairs violates the Minimum Depth set in the type.
TreadDepthFailsEq The actual tread depth and riser height for one or more stairs of this type violates the stair equation.
TreadDepthTooBigFailure The tread depth is too large for the spiral run.
TreadFrontProfileInvalid This profile cannot be used for the front of treads. Please choose a profile composed of a closed loop of lines with exactly one lines coincident with the y-axis. This lines will define the connection of this profile to the tread.
UnableToCreateMultistoryStairs Unable to create Multistory stairs.
UnexpectedCurveIntersectionFailure Computing curve intersection and find the invalid result.
WinderFilletRadiusTooLargeFailure The value for Fillet Radius is too large to satisfy the Minimum Inside Width value.
WinderFirstLegTooShortOrRunWidthTooGreatFailure The first leg of winder run is too short or the runwidth is too great.
WinderGenericError Cannot make winder.
WinderLegIsTooShortFailure A winder leg is too short.
WinderLegsAngleTooGreatOrRunWidthTooSmallFailure The angle between two consecutive legs are too great or the runwidth is too small.
WinderLegTooShortOrRunWidthTooGreatFailure One leg of the winder run is too small or the runwidth is too great.
WinderMinWidthTooLargeFailure The value for Minimum Width on Inside Boundary is too large.
WinderMinWidthTooLargeForParallelTreadsFailure The value for Minimum Width on Inside Boundary is too large to satisfy the number of Parallel Treads at the Start or End as specified in the Run Instance properties.
WinderParallelLegsFailure Two consecutive legs are parallel.
WinderParallelTreadsNumberFailure Cannot satisfy the number of Parallel Treads at the Start or End as specified in the Run Instance properties
WinderRunCreationFailure The relationship between the current values of Actual Run Width, Minimum Width at Inside Boundary, and Parallel Treads at Start or End does not support the creation of the winder run.
WinderRunInsideMinTreadDepthFailure Please enter a positive value less than Actual Tread Depth on Stair Path (%Actual Tread Depth%).
WinderRunInsideWalklineOffsetFailure Please enter a value between 0 and half of Actual Run Width (%1/2 Actual Run Width%).
WinderRunWidthLessThan2TimesMinWidthFailure The value for Minimum Width on Inside Boundary is too large to satisfy the number of Parallel Treads at the Start or End as specified in the Run Instance properties.
WinderRunWidthLessThanWalkLineOffsetFailure The value for Run Width is less than two times of value of the inside walkline offset.
WinderRunWidthOrMinWidthOrTooGreatParallelTreadsFailure The parameter runwidth is great or the parameter min width at inside boundary is too great, or number of parallel treads at both ends is too great.
WinderRunWidthOrMinWidthOrTooShortFailure The parameter runwidth is too great or the parameter min width at inside boundary is too great, or one leg of winder run is too short.
WinderSecondLegTooShortOrRunwidthTooGreatFailure The second leg of winder run is too short or the runwidth is too great.
WinderStraightStepsNumberFailure The current layout cannot allow the specified number of treads. Increase the length of the run leg in the model or reduce the value for Parallel Treads at Start or Parallel Treads at End.
WinderThirdLegTooShortOrRunWidthTooGreatFailure The third leg of winder run is too short or the runwidth is too great.
WinderTooManyEndParallelTreadsOrRunWidthFailure The number of parallel treads at end is too great or the run width is too great.
WinderTooManyParallelTreadsAtEndFailure The number of parallel treads at end is too great.
WinderTooManyParallelTreadsAtHeadFailure The number of parallel treads at start is too great.
WinderTooManyStartParallelTreadsOrRunWidthFailure The number of parallel treads at start is too great or the run width is too great.